Understanding Torque Converters

The torque converter plays a number of roles for a motor vehicle:

  • Multiplies torque generated by the engine
  • Serves as an automatic clutch which transmits engine torque to the transmission
  • Absorbs torsional vibration of the engine and drivetrain
  • Smoothes out engine rotation
  • Drives the oil pump of the hydraulic control system

In simple terms, the torque converter provides a means of power from the engine to the input shaft of the transmission. It acts like an automatic clutch to engage engine torque to the transmission and also allows the engine to idle while the vehicle is standing still with the transmission in gear.

The torque converter can either multiply the torque generated by the engine or function as a fluid coupling. It also serves as the engine flywheel to smooth out engine rotation as its inertia helps to maintain crankshaft rotation between piston power pulses. It tends to absorb torsion vibration from the engine and drivetrain through the fluid medium since there is no direct mechanical connection through the converter.

In addition, the rear hub of the torque converter body drives the transmission oil pump, providing a volume of fluid to the hydraulic system. The pump turns any time the engine rotates, which is an important consideration when a vehicle is towed. If the vehicle is towed with the drive wheels on the ground and the engine is not running, the axles drive the transmission output shaft and intermediate shaft on bearings that receive no lubrication. There is a great potential for damage if the vehicle is towed for a long distance or at greater than low speeds.

The torque converter is mounted on the input side of the transmission gear train and connected to a drive plate. The drive plate, or flex plate is used to connect the converter to the crankshaft flywheel flange of the engine. The ring gear, which the starter motor engages to turn the engine, is attached to the drive plate.

Torque Converter Components

The torque converter has three major components: the Pump Impeller (or Impeller), the Turbine Runner (or Turbine) and the Stator.

Pump Impeller – is integrated with the torque converter case, with many curved vanes that are radially mounted inside. A guide ring is installed on the inner edges of the vanes to provide a path for smooth fluid flow. When the impeller is driven by the engine crankshaft, the fluid in the impeller rotates with it. When the impeller speed increases, centrifugal forces cause the fluid to flow outward, toward the turbine.

Turbine Runner – is located inside the converter case but is not connected to it. The input shaft of the transmission is attached by splines to the turbine hub when the converter is mounted to the transmission. Many cupped vanes are attached to the turbine. The curvature of the vanes is opposite from that of the impeller vanes. Therefore, when the fluid is thrust from the impeller, it is caught in the cupped vanes of the turbine and torque is transferred to the transmission input shaft, turning it in the same direction as the engine crankshaft.

Before moving onto the next component of the torque converter, we need to examine the fluid cupling whose components we have just described. When first automatic transmissions were introduced in the 30’s – 40’s, the only components were the impeller and turbine. This provided a means of transferring torque from the engine to the transmission and also allowed the vehicle to be stopped in gear while the engine idles. However, these early fluid couplings had the problem of poor acceleration. The engine would labour until the vehicle picked up speed. The problem occurred because the vanes on the impeller and turbine are curved in the opposite direction to one another. Fluid coming off of the turbine is thrust against the impeller in a direction opposite to engine rotation.

Notice the illustration of the stator below. The arrow drawn with the dashed lines represents the path of the fluid if the stator was not there, such as in a fluid coupling. Not only is engine horsepower consumed to pump the fluid initially, but now it also has to overcome the force of the fluid coming from the turbine. The stator was introduced to the design to overcome the counterproductive force of fluid coming from the turbine opposing engine rotation. It not only overcomes the problem, but also has the added benefit of increasing torque to the impeller.

Stator – is located between the impeller and the turbine. It is mounted on the stator reaction shaft which is fixed to the transmission case. The vanes of the stator catch the fluid as it leaves the turbine runner and redirects it so that it strikes the back of the vanes of the impeller, giving the impeller an added boost of torque. The benefit of this added torque can be as much as 30-50%.

The one way clutch allows the stator to rotate in the same direction as the engine crankshaft. However, if the stator attempts to rotate in the opposite direction, the one way clutch locks the stator to prevent it from rotating. Therefore, the stator is rotated or locked depending on the direction from which the fluid strikes against the vanes.







  • 2009-11-03

    Volvo I-Shift

    A transmission with intelligence....

  • 2009-10-29

    Honda i-shift

    Honda's i-SHIFT System offers Civic buyers the opportunity to rest the left foot

  • 2009-10-18

    WEBSHOP - Oil filter VW 6 speed

    We can offer oil filters for latest type of VW 6 speed transmissions

  • 2009-10-07

    WEBSHOP - Oil Pump 5L40E

    KAPS reconditioned oil pump for the 5L40E automatic transmission!

  • 2009-10-06

    Aston Martin DBS Touchtronic

    The ultimate Aston Martin is only a year old, but it's already getting some updates including a new automatic transmission.

  • 2009-09-23

    ZF Powerline Automatic

    Nissan is preparing to launch an all-new line of light commercial vehicles for the North American market in 2010 with ZFs powerline.

  • 2009-09-21

    WEBSHOP - Multitronic 01J kit (Audi)

    Spare parts kit for the Multitronic 01J (Audi) automatic transmission.

  • 2009-09-08

    Peugeot ECG

    The Peugeot Electronic Controlled Gearbox (ECG) in the 207 and 308 models.

  • 2009-08-27

    WEBSHOP - Piston kit 5L40E

    Yes we sell spare parts! Piston Kits available for Automatic Transmission 5L40E.

  • 2009-06-17

    Antonov TX6 Automatic

    In the Antonov TX6, the torque converter has been replaced with a pair of wet clutches - one for forward gears and one for reverse

  • 2009-06-10

    Zeroshift 8 Speed FWD Transmission

  • 2009-06-10

    Porsche Doppelkupplung (PDK)

    PDK is essentially two half gearboxes in one and thus requires two clutches – designed as a double wet clutch transmission

  • 2009-06-03

    MC Shift Technology

    This electro-actuated gearbox can change gears in as little as 100 milliseconds – faster than any driver could achieve with a conventional manual transmission!

  • 2009-05-27

    Modern Gearbox Technology

    Confused by the slew of abbreviations like DSG, SMG, CVT, and the like? You aren't alone.

  • 2009-05-20

    BMW DCG - Double Clutch Gearbox

    Wave goodbye to BMW's SMG sequential manual gearbox and say hello to its new DCG double clutch gearbox.

  • 2009-05-19

    BMW SMG Gearbox

    Looking back to 2002 with BMW’s SMG – Sequential Manual Gearbox

  • 2009-05-10

    Original Autos - Hydra Matic

    We take a look at the birth of the Automatic Transmission.

  • 2009-05-10

    Original Autos - Dynaflow

    We take a look at a second original Automatic Transmission.

  • 2009-04-30

    Automatic vs Manual Transmission

    We compare the major points in the debate between Manual and Automatic Transmissions. What is better for you?

  • 2009-04-30

    JaguarDrive Selector

    What is the JaguarDrive Selector?

  • 2009-04-22

    Ford Dual Clutch Powershift

    PowerShift will deliver the fuel efficiency of a manual gearbox with the convenience and ease of a premium automatic transmission

  • 2009-04-22

    Ford 6F-55 Select Shift 6 Speed

    A six-speed SelectShift automatic transmission that's specifically designed for the higher torque demands of the all-new twin-turbocharged, direct injection engine.

  • 2009-04-16

    Understanding the Valve Body 1/2

    The Valve Body of an automatic transmission contains a complex series of passages controlled by valves to direct fluid flows. We will look how this functions. Part 1 of 2

  • 2009-04-16

    Understanding the Valve Body 2/2

    The Valve Body of an automatic transmission contains a complex series of passages controlled by valves to direct fluid flows. We will look how this functions. Part 2 of 2

  • 2009-04-08

    Understanding the Lock Up Clutch

    This article will look at the operation and fluid flows controlling the lock up clutch machanism.

  • 2009-04-08

    Stall Torque Converters

    What are the pros and cons of a stall torque converter? What is their best application?

  • 2009-04-02

    Understanding Torque Converters

    In this article we look at the role of a Torque Converter in an Automatic Transmission and discuss its components.

  • 2009-04-02

    Understanding Converter Fluid Flows

    Previously, we looked at the parts that make up the torque converter and had a brief introduction on the workings of each component. We will focus this article of the fluid flow within the torque converter itself.

  • 2009-03-26

    Understanding Holding Devices for Planetary Gear Sets

    In this article, we will look at the three common types of holding devices for planetary gear sets. Each having their own distinct advantages.

  • 2009-03-25

    Understanding Planetary Gears

    This article will look at the design of planetary gear sets in an automatic transmission.

  • 2009-03-18

    Hyundai’s 6-speed Transaxle Automatic Transmission

    Designed for cleaner emission regulations and better fuel economy, by as much as 12.2%!

  • 2009-03-18

    Understanding Automatic Transmissions

    Over the coming weeks, we will look at various components of the automatic transmission. This article discusses the basics of the auto transmission.

  • 2009-03-10

    Product Info - Shell Donax Oil

    Shell Donax TX is a premium performance, semi-synthetic heavy-duty universal power shift and automatic transmission fluid

  • 2009-03-10

    Product Info - Petro-Canada Oils

    Introducing the next generation of Automatic Transmission Fluids

  • 2009-02-16

    ZF Develops Automatic 8-Speed Transmission

    Consumption savings of six percent thanks to the new transmission concept with improved efficiency

  • 2009-02-11

    VW 7 Speed DSG

    DSG – the intelligent automatic gearbox from Volkswagen World’s first 7-speed DSG for high-volume production

KAPS Automatic s.r.o. Prerovska 561, 752 01 Kojetin, Czech Republic
+420 581 764 086
  • Pioneering innovations

    Carl F. W. Borgward quickly and automatically shifted gear

  • World record with GTR

    Congratulations to Mike Newton and Litchfield’s achieving the world record of the “Fastest Blind Man” in the world at 200.9mph.

  • Proffesional ATF products on offer!

    Professional ATF products now on sale at our eshop www.kaps-parts.com. View more..

  • Two Mass Flywheel DSG

    Two Mass Flywheel for DSG transmission for the best price on the market!! If you hear unnatural sound, its time to exchange your Two Mass Flywheel now. Use: engines 1.9 TDI (77kW) code BLS vehicles VW, Audi, Skoda, Seat. With the Two Mass Flywheel you can keep the engine running at a very low speed idle on modern engines.

  • Oils and Fluids

    You can now order Oils and Fluids through our eshop. Please check www.kaps-parts.com.